Habibberi Agil Rabani

Universitas Singaperbangsa Karawang

Iman Dirja

Universitas Singaperbangsa Karawang

Najmudin Fauji

Universitas Singaperbangsa Karawang

DOI: https://doi.org/10.19184/rotor.v15i1.31474 

ABSTRACT 

The rapid development of the manufacturing industry requires companies to always produce high quality and fully functional products. However, when the production process does not always run, there should be problems encountered, such as the machine factor which often breaks down and even shuts down completely, causing production disruption. One of the important factors in the successful implementation of Failure Mode Effect Analysis (FMEA) is to interpret before, the process takes place and not after it occurs. To support the implementation of Failure Mode Effect Analysis in the field of maintenance, an effort is needed to improve the state of the equipment. So, in this study, this method will be applied to the maintenance of the Gemini Ficep G25 CNC machine. The result can be assumed to be the primary problem in damage. The trouble that must be prioritized first are the plasma doesn’t run, the force on the engine drive does not move, the dust collector does not work and the internal and external coolants water don’t come out.

Keywords: FMEA, Pareto, CNC, Maintenance.

REFERENCES

[1] D, Mayangsari. H, Adianto dan Y, Yuniati. 2015. Usulan pengendalian kualitas produk isolator dengan metode Failure Mode And Effect Analysis (FMEA) dan Fault Tree Analysis (FTA).  Jurusan Teknik Industri Itenas. Vol. 03,  pp. 81-91.

[2] Suherman A dan Cahyana B, J. 2019. Pengendalian kualitas dengan metode  failure mode and effect analysis (FMEA) dan pendekatan kaizen untuk mengurangi jumlah kecacatan dan penyebabnya. Seminar Nasional Sains dan Teknologi. pp. 1 – 9.

[3] Abdul Wahid Muharram dan Razali. 2020. Analisis Resiko Kerusakan pada Mesin Doosan GV180 TI dengan Menggunakan Metode FMEA. Jurnal Inovtek Seri Mesin. Vol. 1 (1), pp. 31 – 35.

[4] M, I, Ramadhan, J, Sumarjo. F, C, Suci dan D, T, Santoso. 2021. Analisa kerusakan pada mesin AHU menggunakan metode Failure method and effect analysis. ROTOR. Vol. 14 (2). pp. 49-53.

[5] R, Z, Yaqin. J, Siahaan. Y, E, Priharanto. M, Alirejo dan M, Umar. 2020. pendekatan FMEA dalam analisis resiko perawatan sistem bahan bakar mesin induk. Jurnal Rekayasa Sistem Industri. Volume 9 (3). pp. 189-199.

[6] Susilo A. Rohimat R, I. Husniah H. 2019. Analisis kegagalan Operasional Mesin Chiller Dengan Metode FTA dan FMEA. Integrasi Jurnal Ilmiah Teknik Industri. Vol. 2 (3). pp. 19 – 29.

[7] Saputra R dan D, T, Santoso. 2021. Analisa kegagalan proses produksi plastik pada mesin cutting di PT. PKF dengan pendekatan Failure Mode and Effect Analysis dan Diagram Pareto. Journal Unsika. Vol. 6 (1). pp. 322-327.

[8] Munaroh L. Amroji Y dan Nurdian R, A. 2021. Pengukuran Risiko Keamanan Aset TI Menggunakan Metode FMEA dan standar ISO/IEC 27001:2013. Technomedia Journal. Vol. 5 (2). pp. 167 – 181.

[9] Muhamad Bob Anthony. 2016. Analisis Penyebab Kerusakan  Hot Rooler Table dengan Menggunakan Metode Failure Mode and Effect Analysis (FMEA). Jurnal INTECH. Vol. 4 (1), pp. 1 – 8.

[10] Kurnianingsih E. Gautama E. M, F, K, Syams. 2021. Usulan perbaikan kualitas dengan menggunakan metode FTA dan FMEA. Jurnal InTent. Vol. 4 (1). pp. 41-54.